Arema Specifications PDF
AREMA Specifications - Chapter 3, Section 6.3.1 Boulton drying or vapor drying process is an acceptable alternative to air seasoning. 90.06 Preservative Treatment. Ties shall be pressure-treated creosote as outlined in AREMA
common gradations listed in AREMA specifications for main line railroads were generated using the University of Illinois ballast DEM model BLOKS3D program. Repeated train loading was applied to the different ballast gradation characteristic curves to investigate the adequacy of
insure that it exceeds both AREMA weld specifications and AWS rail welding specifications. The rolling load test of a flash butt wedge weld showed no erratic wear patterns or any signs of crack initiation.
Chapter 30 of the AREMA Manual for Railway Engineering. This publication does not include numerous other requirements of AREMA specifications. AREMA Manual Chapter 30 is a multi-page work covering many additional practices
American Railway Engineering and Maintenance of Way Association (AREMA) Specifications. American Society for Testing and Materials (ASTM) Specifications. American Water Works Association Standards and Specifications, AWWA, 2 Park Avenue, NY, NY 10016.
Caltrain Standard Specifications 18370-3 September 30, 2011 SIGNAL WIRE AND CABLE 2. Track wire shall meet the recommendations of AREMA C&S Manual, Part
AREMA specifications, Chapter 5, “Track”, with punched A-8 square spike holes shall be used to replace any broken or missing tie plates.
Caltrain Standard Specifications 20500-1 September 30, 2011 SPECIAL TRACKWORK SECTION 20500 SPECIAL TRACKWORK PART 1 - GENERAL ... shall be 3-shot explosion-hardened in accordance with AREMA Specifications. Heel of the frog shall incorporate a 30-degree cut.
Specifications) of the current AREMA Manual. Sub-Ballast material shall conform to the grading requirements as shown in Table 6. Description: Any material of a superior character spread on the finished sub-grade of the roadbed and
WisDOT Bridge Manual Chapter 38 – Railroad Structures July 2013 38-4 38.2 Design Specifications and Design Aids 38.2.1 Specifications Allowable stresses are provided in different chapters and sections of the AREMA Manual.
NOTE: If other than AREMA, ASTM, or AWWA specifications are referred to for design, materials, or workmanship on the plans and specifications for the work, then copies of the applicable sections of such
AREMA Specifications for Waterproofing (Chapter 29) 4.2.4. The Standard Specifications of the State’s Highway Department or local agency responsible for the design and construction of highway bridges 4.2.5.
www.lbfoster.com 866.523.7245 Scale: Drawing is actual size specifications, 40 FT, 80 FT 39 FT 40 FT 80 FT
Where conflict exists between the AREMA Manual and these specifications, these specifications shall govern. In addition, construction must adhere to all Federal Railroad Administration (USA) or Transport Canada requirements.
details that meet the requirements of AREMA design specifications as well as the requirements of the governing railway. Fracture Critical Members (FCM) The AREMA Manual for Railway Engineering defines and describes Fracture Critical
Permissible Variations in Completed Switches; the AREMA “Specifications for Special Trackwork”, Permissible Variations in Dimensions, Fits and Other Physical Attributes , page 100-92, Section 7. ; and the AREMA “Specifications
Roadway and Ballast SECTION 2.0 SUBSTRUCTURE INTRODUCTION 2.0.1 DESCRIPTION (1991) This part of these Specifications shall cover the design, materials, evaluation, production, construction and
AREMA American Railway Engineering and Maintenance of Way Association Subsection 101.38 General Notices: (2/23/2011) Add the following before General Notices: ... These Specifications, Supplemental Specifications, Plans, Special Provisions, and
Specifications, AREMA requirements and within tolerance. The guard rail shall be fully assembled to the layout rail. 184.108.40.206 Contractor quality assurance report shall be provided to WMATA. The report shall be completed and submitted to the COTR for approval
V. INTERFACING WITH EXISTING CONCRETE A. Surface preparation and anchorage shall be as specified in AREMA Specifications, Chapter 8, Part 14, unless
to the most current AREMA Specifications for Low Carbon Steel Track Spikes. A minimum of two spikes per tie plate is required on tangent track. Spikes through the turnout should be applied in the number and location required in
38.2 DESIGN SPECIFICATIONS AND DESIGN AIDS 4 (1) Specifications 4 (2) Design Aids 4 (3) Horizontally Curved Structures ... AREMA calls for compensation for curvature of up to 1.5 inches per degree of curve. Refer to AREMA Chapter 28.
All transportation systems (highways, runways, railways) have engineering specifications relative to vertical and horizontal clear zones. These clear zones or “clearances” provide a ... (AREMA). These guidelines are used by individual railroads, railroad engineering firms, ...
are designed in accordance with AREMA specifications and can be customized to meet customer requirements. CXT concrete ties will improve reliability of existing tracks and build longterm performance into tomorrow’s industrial applications, ...
AREMA MRE, Specifications for Steel Rails, Chapter 4, Part 1, and Standard Plan Nos. 1300 and 1302. Drill holes with an approved rail drill. 4. Drill cylindrical holes of diameter specified by AREMA for the size bolt required,
AREMA: American Railway Engineering and Maintenance of Way Association Manual for Railway Engineering ... Only those imperfections that are within the limits of current AREMA and RTA specifications will be allowed. A split is a separation of the wood extending from one surface to an opposite or ...
AREMA Specifications, and shall fit rail being used. For rail 110# section and greater, all plates will be double-shouldered. Joints: New or secondhand joints, free of foreign material and without injurious defects, and with 4 or 6 bolt
Interoperable Positive Train Control (PTC) William A Petit www.BillPetit.com AREMA 2009 Annual Conference Communications and Signals Track Abstract: This paper discusses architecture, interoperability and status of an Interoperable Communication Based Signaling (ICBS)
with AREMA and industrial specifications and designs can be modified to meet any requirement. You can specify all individual components from switch points, fittings, switch rods, stands and replacement parts, to complete switches
American Railway Engineering and Maintenance Association Specifications. Where local laws or authorities prescribe a more stringent specification, ... protection as provided in the AREMA Manual for Railway Engineering, Chapter 8, Section 2.1.5.
Design and detailing shall comply with AREMA specifications except as modified in these guide specifications and as directed by the Authority Page 27 of28 October 2005 . 9.7.1. Material Concrete masonry units shall meet the requirement of ASTM C145 and C90, Grade N,
SPIKES Track spikes are manufactured to AREMA specifications in both soft steel and high carbon varieties. In addition, good quality industrial grade spikes are stocked in the larger spike sizes.
1313---111 AMERICAN RAILWAY ENGINEERING AND MAINTENANCE OF WAY ASSOCIATION Practical Guide to Railway Engineering Case Studies Chapter ©2003 AREMA®
AREMA Specifications: Refers to the American Railway Engineering and Maintenance of Way Association Specifications, Volumes I and II, and Portfolio of Trackwork Plans. 090010.03 MATERIALS. A. Rail. 141 pound relay rail.
• Exceeds the AREMA specifications for both arrestor and equalizer applications • Provides a 50kA 8/20 maximum surge rating for protection that is suitable for exposed trackside equipment • Available in various operating voltages to suit most common rail
NOTE: If other than AREMA, ASTM or AWWA specifications are referred to for design, materials or workmanship on the plans and specifications for the work, then copies of the applicable sections of such other
Rail shall control cooled to AREMA specifications. Rail shall be rolled in accordance with the general physical dimensional requirements of AREMA design but shall meet the Section tolerances and Chemical Composition listed below. SECTION TOLERANCES
with the project specifications, AREMA Manual, these guidelines and structural capacity before forwarding the submittal to the Railroad. GUIDELINES FOR TEMPORARY SHORING, Published October 25, 2004 14 3. Review process.
in accordance with AREMA and owner specifications. L.B. Foster’s concrete ties have high flexural strength and have been developed to work in conjunction with the fastening system and ballast to resist lateral, longitudinal and vertical movement while in track.
difference between the AASHTO LRFD Specifications and the AREMA Manual is the live-load model. AREMA specifies the Cooper E 80 load, which is 18 concentrated axle loads followed by a trailing uniform load, or a fraction thereof for each track.
9/13 .5M In the interests of product improvement, Pandrol reserves the right to change the specifications contained herein at any time without prior notice. VICTOR VICTOR with ... excess of AREMA specifications for concrete tie shoulders
Maintenance-of-Way Association (AREMA) Specifications. In the event of conflict, the drawings, these specifications, and the current AREMA Specifications shall govern respectively. B. The Contractor is advised to familiarize himself with the AREMA Specifications contained in Chapter
115-lb A.R.E.M.A. specifications 24" length, 72 lbs. per pair. 36" length, 107 lbs. pair. 1" x 5 1/2" button head, oval neck track bolt with heavy square nut.
SPECIFICATIONS AREMA® Specification; Chapter 29 for Membrane Waterproofing. FEATURES/BENEFITS joints of the first layer. No ... AREMA® specification in Chapter 29 E. • Eliminates messy hot-mopping and cold-bitumen adhesives.
Applicant must provide pipe specifications. Pipe must satisfy AREMA recommendations and all applicable government and industry regulations. 5. Applicant must provide qualifications of drilling contractor including specific instances of previous
STANDARD SPECIFICATIONS . SECTION 02420 . TUNNELING . PART 1 . GENERAL . 1.1 DESCRIPTION . ... D. Follow AREMA or other applicable railroad specification and permit requirements. PART 2 . PRODUCTS . 2.1 MATERIALS . 02420-2 April 2009 . A. Liner Plates.
One lock washer conforming to AREMA Specifications shall be installed on each track bolt. Ballast: Ballast shall be minimum of AREMA size 5 (1" - 3/8"). Ballast shall be free from loam, dust, and other
Track spikes are manufactured to AREMA specifications in both soft steel and high carbon varieties. In addition, good quality industrial grade spikes are stocked in the larger spike sizes. Industrial grade ... AREMA Reinforced Throat
Specifications for Bridge Timbers For Bridge Timber Specifications please refer to AREMA Chapter 7 Timber Structures. Specifically to Table 7-2-9 "Allowable Stresses for Stress Graded Lumber -
AREMA Specifications shall govern respectively. B. The Contractor is advised to familiarize himself with the AREMA Specifications contained in Chapter 8, Concrete Structures and Foundations, Part 1, Materials, Tests and Construction Requirements, Part 14, Repair and